Product Information
Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates$288.00 – $728.00
The CMC Manual Jack Plates from Boaters Catalog has comparable design and construction features as the hydraulic lift without the convenience of automated adjustment.
If you desire engine performance enhancement, but don’t have the budget for our hydraulic unit then the ML-65 may be exactly what you are looking for. Our manual units provide similar benefits to the hydraulic units. However, since you cannot raise or lower the engine as you are moving you will not receive the same performance enhancements associated with a hydraulic unit.
The 4 and 5-1/2 inch set back plates are rated for V-6 and smaller motors. They are NOT designed for V-8 or racing applications.
Manual ML-65HD, item#65512 rated for V8 400HP outboards or smaller.
(See description below for transom washer plates and wedges.)
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Description
Manual Jack Plates
One Piece Manual Features:
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• Centrally located adjustment screw for positive alignment
• 5 1/2″ and 10” Set Backs from Transom are available
• 5″ Vertical Adjustment
• Designed to fit standard B.I.A. bolt pattern
• Aluminum models rated for up to V6 outboards
Two Piece Manual Features
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• 4” and 5 1/2″ Set Backs from Transom are available
• 5” of slot adjustment at the motor mounting bracket
• 1 ½” of adjustment at the transom bracket.
Manual ML-65HD, item#65512 rated for V8 400HP outboards
Transom Support Plates / Transom Washer Plates
Made of strong 3/8″ 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts “biting” into transoms and can more evenly distribute loads on high performance engines.
Hole centers: Top Plate – 12 7/8″ Bottom Plate – 9 7/8″
Transom Wedges and Setback Spacers (Item #20122)
These 2 degree wedges are designed to give extra positive or negative trim.
Features:
Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed
Unique design of the CMC Transom Wedges allows you to also use them as set back spacers
Simply stack and invert 2, 4, and 6 sets (sold in sets of two)
Fit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt pattern
Made of strong 6061 T6 alloy aluminum (not cast aluminum)
- 65012- ML-65-5 1/2 with 5 1/2 inch set back - DIM. 18 1/8"W x 15 1/5"H Weight 32#
- 61012 - ML-65-10 with 10 inch set back - DIM. 18 1/8"W x 15 1/2"H Weight 43#
- 55012 - 2 Piece Manual w/5-1/2" setback 18 1/8" x 15 1/2"H (mounted) Weight 23#
- 40012 - 2 Piece Manual w/4" setback - DIM. 18 1/8"W x 15 1/2"H (mounted) Weight 20#
Related Products
Deluxe Step Box with Storage 2
Our Deluxe Step Box with Storage 2 has sleek rounded edges, built in non skid surface on top of the steps and Euro-style chrome brass handles.
W 22" x H 14" x D 17.5"
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products
Single Step Box
Our Single Step Box from Boaters Catalog has sleek rounded edges, built in non skid surface on top of the steps, Euro-style chrome brass handles and all cut and exposed edges are gelcoated.
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products at this time.
Anchor Line and Chain
Captain Charlie's™ Anchor Line and Chain from Boaters Catalog is custom fabricated to meet your specific needs. We can custom cut any length of line or line and chain combination that you want in any sizes that you need.
The combinations that you see here are the most popular lengths and sizes that are appropriate for many electric windlasses. Please remember that not all windlasses use the same size and type of line or the same chain. Most will only pull the type of rode they are designed for. The 8 Brait line is compatible with both Lewmar and Powerwinch and will take up much less room in your anchor locker.
If you want something other than what you see here, please call 800-745-0765 or e-mail us with your specifications and we will be glad to call you back with a quote.
Freight will not be figured by the shopping cart. We will contact you when your order is received with your freight quote.close
25 inch Center Console
Our 25 inch Center Console from Boaters Catalog has an average fiberglass thickness of 1/4"-3/8". Also the dash is reinforced with 11 mm Nida Core. This console is perfect for small skiffs 13'-16' long.
25"H x 21"W x 16"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 21"W x 16"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
Windlass Service Spares and Parts
Windlass Service Spares and Parts
We have access to parts for Lewmar, Horizon, Sprint, Simpson Lawrence, James Neilssen, Maxwell, and Quick. Many of the older uiits have no parts available but we won't know until we check with our US supplier. Some are available from Scotland, but they are more expensive and take a longer time to acquire.
If you need parts or service on your windlass, call us at 800-745-0765, Monday - Friday 9 am - 4 pm EST.
Pet Dining Mats
Our Custom Embroidered Pet Dining Mats from Boaters Catalog are Made of MARINE GRADE plush carpet that is antimicrobial, with a non-skid rubber backing. All edges are beautifully finished with poly binding. We provide custom embroidery to match. We offer your custom pet mat in 4 sizes based on your pets' size. Our mats are easy to clean and our bowls are Stainless Steel and dishwasher safe, 2 stainless steel bowls per Pet Feeding Set.
Sizes are:
- Small- 12x20 mat with 2 ea. 8oz bowls(good for cats)
- Medium- 17x24 mat with 2 ea. 16oz bowls
- Large- 17x27 mat with 2 ea. 32oz bowls
- Xtra-Large- 18x30 mat with 2 ea. 64oz bowls
- Included-Add your personalization just for your pet!
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Pet Feeding Mat is customized with your embroidered pet name or other text, adding that personal touch.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing.
Our premium Marine Carpet Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 10-14 business days from the time of your order until it is shipped.
See our color charts below as you choose your carpet options.
See our other quality boat and dock products here.
Bench Seat
Our Bench Seat from Boaters Catalog is a super comfortable fiberglass bench seat that can be used for a boat, pool area, patio, or on a dock. It seats 2 adults or 3 children comfortably. It has an Ultra-violet resistant white gelcoat. The seat from top to bottom is 16".
- 43"L x 30"D x 26"H
There is an 11 week lead time on our fiberglass products at this time.
48 inch Center Console
Our 48 inch Center Console from Boaters Catalog has large rounded corners and is perfect for boats 16' to 18' long. This product is great work boat size because it is tall and narrow.
48"H x 24"W x 24"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
This product is great work boat size because it is tall and narrow.
48"H x 24"W x 24"D
Additional measurements
- 22 inch x 14 inch section that holds the steering and controls
- 21 inch x 10 1/2 inch part that angles down from the top facing the driver
- 21 inch x 7 inch, the flat part on the top
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
15 Inch Pull Up Cleat
Our 15 Inch Pull Up Cleat from Boaters Catalog is THE LARGEST FLUSH-MOUNTED CLEAT AVAILABLE! Its the perfect cleat to keep the gunwale and bow of your vessel clean and sleek looking at the same time avoiding a trip hazard.
FEATURES:
- The largest flush-mounted cleat available!
- Made of marine grade 316 stainless steel.
- Available in both stud mount and through-bolt versions.
- Stud length is 4" on part # 115-15-S.
- Each cleat is supplied with a waterproofing cup(shown).
INSTALLATION
- Each cleat is shipped with a backing plate which also serves as the cut-out template.
- Fasten with four 3/8" diameter screws (not included),weight = 16 pounds each.
Available with visible screw holes as PN 115-15 (load of 61,000 pounds), or with studs on the underside of base as PN 115-15-S (load of 31,000 pounds).
Shipping weight 19#
Proper maintenance consists of rinsing with fresh water regularly, and following each exposure to salt water. Stainless steel surfaces should be periodically wiped with a clean, soft cloth. Plastic surfaces may be cleaned with a mild, non-abrasive detergent solution, then rinsed with fresh water as necessary.