Important Information...
Online Policies
International Sales
Shipping and Returns
Your Privacy Matters
Talk to Us!
Description
Description
Minnow Fin For Trolling Motors
The Minnow from Boaters Catalog installs in minutes with just a screwdriver. It will provide directional assistance whenever it is in the water. The steering response is improved when using thrust or when using another motor for propulsion. If fishing conditions require drifting and working the current while stalking the ‘Elusive Lunker’ the minnow will add stability and limit wind effect. Fight the fish, not your boat. Tested and proven effective by Northwest fishermen.
BENEFITS
- 10X the Steering Control
- 3X the Turn Rate
- 10X the Effective Rudder Area
- Exceptional Tracking in Windy and Turbulent Conditions
- Reduced Cycling of the Autopilot because the steering is more effective.
- Maximizes the thrust of your electric trolling motor.
FEATURES
- Marine Aluminum
- Welded construction
- Fits virtually all modern electric trolling motors
- Simple 5 minute installation with only a screw driver.
- Patent Pending
- Made in the USA
Related Products
Quick View
Static Jack Plate 5 inch
Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates, Outboard Tilt and Trim
The CMC Static Jack Plate 5 inch vertical outboard motor extension allows the motor to be mounted 5 inches higher than the
standard mounting height on the transom.
It is a must for easy conversion from prop drive to jet drive.
Another application includes mounting the 5 inch vertical extension on a hydraulic jack plate to raise the motor higher on shallow running boats that are equipped with tunnel extensions.
Constructed of Extruded 6061-T6 Aluminum alloy. (#50012) They are 5” wide and 20-1/2” long. It is rated for 300 HP and smaller motors.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Quick View
Cleat Rod Holder Combo
Customize Your Vessel, Improve or add to the rod holders on your boat, Improve the hardware on your boat, Other Boat Hardware, Pop Up and Pull Up Cleats
Keep your Gunnels Free From Extra Hardware! Our Pull Up Six Inch Cleat Rod Holder Combo eliminates the need for two separate installations.
FEATURES
- Made of marine grade 316 stainless steel.
- Saves Room on the gunnel. Eliminates the need for two separate installations.
- 30-degree angle
- 7.57" long, 3.74" wide, 8.38" deep
INSTALLATION
- Fasten with four 1/4" diameter screws (not included).
Quick View
Troll Plate Fin
Our Troll Plate Fin from Boaters Catalog will give you the control and stability that you've been missing. Uncle Norm’s Troll Plate Fins triples the effective rudder area giving you powerful directional control at very slow speeds and adds crisp responsiveness at any speed. Fins on trolling plates are a great help tracking on course when trolling during windy conditions or in current. Included are 2 fins that bolt onto your troll plate. Troll plate is not included.
Quick View
CMC Hydraulic Jack Plate
This dependable, self contained, and water proof CMC Hydraulic Jack Plate from Boaters Catalog has a maximum lifting capacity of 7,853 pounds of thrust. You will have no problem lifting even a V-6 300 hp max. motor at full throttle. The hydraulic actuator is mounted inside the structure of the Power-Lift, yet it is fully accessible without removing the engine. There are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks.
The catalog cannot determine freight accurately. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Price range: $1,179.00 through $1,601.00
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Boat Tool Holder
Customize Your Vessel, Fishing Tools, Improve the hardware on your boat, Improve your beach or dock fishing experience, Improve your fishing tackle, Other Boat Hardware, Snap-N-Trac Organizer System
All-in-one, customizable Boat Tool Holder from Boaters Catalog for lures, pliers, knives, hook extractor, and cup holder.
Customize the Snap-N-Trac the way you want! 3 different designs with the one kit.
Lay the pieces out any way you like. Simply attach the trac then snap in the pieces in the design you prefer.
Can be installed where other systems cannot!
Add more kits to hold more stuf!
Quick View
High Speed Hydraulic Power Lift
This dependable, self contained, and water proof High Speed Hydraulic Power Lift from Boaters Catalog has a maximum lifting capacity of 7,853 pounds of thrust. With the CMC High Speed Hydraulic Power-Lift you will have no problem lifting even a V-6 300 hp max. motor at full throttle. The hydraulic actuator is mounted inside the structure of the Power-Lift, yet it is fully accessible without removing the engine. There are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks.
The hydraulic actuator is completely self-contained with its own fluid reservoir (eliminates the need for hydraulic tank and hoses inside the boat). It contains a permanent magnet motor for more power and constant torque. The cylinder within the actuator has twice the lifting capacity than other transom jacks on the market. It contains a no-leak seal and wiper that keeps dirt and water out of the working parts. The system is made of 100% non-ferrous material which makes it impervious to saltwater and freshwater.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Price range: $1,179.00 through $1,601.00
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Static Jack Plates
CMC Static Jack Plates
The 2-1/2 INCH CMC Static Setback Jack Plate has 1 ½” of height adjustment at the transom. It can be used as a stand-alone 2 ½” setback plate or used in conjunction with another manual or hydraulic jack plate to give an additional 2 ½” of setback. Constructed of Extruded 6061-T6 Aluminum alloy. (#65213)
The 7 INCH CMC Static Setback Jack Plate has 1 ½” of height adjustment at the transom bracket and 1” of height adjustment on the motor bracket. The dimension from the top of the transom to the top of the motor side is 3 ½”. Constructed of Extruded 6061-T6 Aluminum alloy and stainless steel fasteners. (#70012)
The 9 INCH CMC Static Setback Jack Plate has 1 ½” of height adjustment at the transom and 1” of height adjustment on the motor bracket. The dimension from the top of the transom to the top of the motor side is 5 ¾”. Constructed of Extruded 6061-T6 Aluminum alloy and stainless steel fasteners. (#90012)
All our CMC Static Setback Jack Plates are built of the finest quality materials and made to accept any bolt pattern for ease of installation.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Price range: $148.00 through $439.00
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Orca Performance Fin
The Orca Performance Fin from Boaters Catalog triples the effective rudder area providing a tighter turn radius and sharp crisp directional control at any speed. The larger surface area of the Orca Performance Fin blocks cavitation better than hydrofoils while adding the benefit of enhanced slow speed maneuvering and heading control. The Orca-Performance Fin installs in minutes without drilling using the 45M-Clamp kit or bolt directly to the cavitation plate using included hardware.
The Orca fin is usually mounted with the fins down but may be installed fins up without modification if you desire less aggressive control. Used and tested on fishing boats, runabouts, pontoon boats, cruisers, ski boats and bass boats (over 80 HP) since 2002.
The New Orca Heavy Duty Fin for outboards over 250 HP is now available, click here.
Quick View
Through Hull Fittings
Customize Your Vessel, Improve the hardware on your boat, Lifting Cleats, Eyes, and Chocks, Other Boat Hardware, Pop Up and Pull Up Cleats
Through hull fittings for drains for your pull up or pop up cleats, lifting rings, or other hardware that you don't want to drain inside the boat.
| PRODUCT # | DESCRIPTION |
| 600 | Brass through hull fitting |
| 601 | Plastic through hull fitting |
| 602 | Stainless Steel through hull fitting |
- For up to 1/4" thick hulls.
- Available in plastic, stainless steel or brass.
- Thread is 3/8-24.
Price range: $4.51 through $11.57
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Tie Down and Ski Tow
Flush Mounted Tie Down and Ski Tow
Tie Down Features
- May be used anywhere equipment must be secured to the deck-e.g. poling platform, scuba gear, fenders, etc.
- Large size (#195) is also ideal for docks; small size (#196) is ideal for personal watercraft.
- Made of cast stainless steel.
- Assembly consists of main body and sealing cup.
Ski Tow Features:
- Keeps the transform clear of protruding ski tows.
- Four piece patented assembly consists of main body, sealing cup, backing plate and gasket.
Price range: $20.65 through $55.87
Select options
This product has multiple variants. The options may be chosen on the product page
