Product Information
Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates$1,460.00 – $1,684.00
The CMC HD Hydraulic Jack Plate PL-65HD Power-Lift from Boaters Catalog is designed for 400 HP outboard motors. The PL-65HD is made of 6061 T6 aluminum alloy extrusions and fastened with stainless steel fasteners for maximum strength and durability. The structure incorporates a patented roller design providing less friction, longer wear, less maintenance and virtually eliminates any chance of binding.
The self-contained and water proof electric hydraulic power unit and cylinder is embodied into one actuator inside the structure of the Power-Lift and includes its own fluid reservoir. Providing a lifting capacity of 7853 lbs of thrust, it has no problem lifting a 400 HP motor at full speed.
The CMC HD Hydraulic Jack Plate is made of 100% non-ferrous material which makes it more impervious to salt and fresh water. This design eliminates the need to install a hydraulic tank, motor, pump and hoses inside the boat saving the boat room where needed. It comes full of fluid, tested and ready for operation.
(See below for a description of transom wedges and washer plates.)
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
See all our quality CMC products for your outboard motor here.
Description
CMC HD Hydraulic Jack Plate for 400 HP
Transom Support Plates / Transom Washer Plates
Made of strong 3/8″ 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts “biting” into transoms and can more evenly distribute loads on high performance engines.
Hole centers: Top Plate – 12 7/8″ Bottom Plate – 9 7/8″
Transom Wedges and Setback Spacers (Item #20122)
These 2 degree wedges are designed to give extra positive or negative trim.
Features:
- Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed
- Unique design of the CMC Transom Wedges allows you to also use them as set back spacers
- Simply stack and invert 2, 4, and 6 sets (sold in sets of two)
- Fit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt pattern
- Made of strong 6061 T6 alloy aluminum (not cast aluminum)
Related Products
25 inch Console with Seat
Our 25 inch Console with Seat from Boaters Catalog has an average fiberglass thickness of 3/8" and has a front seat molded into console. This product is perfect for boats 15' to 18' long.
25"H x 26"W x 31"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 26"W x 31"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Deluxe Step Box with Storage
Our Deluxe Step Box with Storage has sleek rounded edges, built-in non skid surface on top of the steps, and Euro-style chrome brass handles.
W 22" x H 12.75" x D 17.5"
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
53 inch High Center Console
Our 53 inch High Center Console from Boaters Catalog has enough space to flush mount all your electronics. Dash mounting area for controls and steering is 34" x 16" and has an average fiberglass thickness of 3/8".
Base measurements including flange are 38" x 38" and height is 53".
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
53"H x 38"W x 38"D
This console is perfect for single or twin engine boats.
Freight will be quoted shortly after your order or you may call 800-745-0765 for a quote.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
35 inch Console with Front Seat
Our 35 inch Console with Front Seat from Boaters Catalog has an overall height of 35" and an over all length including flange is 43 1/2". Rear including flange is 38" and front including flange is 32". This console is perfect for boats 21' to 25' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
Front seat is so your passenger can safely sit on the center line of the boat.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
35"H x 36"W x 43-1/2"D
Additional measurements:
- Rear width including flange 38"
- Front width including flange 32"
- Seat approx 15-1/2" high from deck
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
30 inch Center Console
Our 30 inch Center Console from Boaters Catalog has large rounded corners and is perfect for boats 15' to 18' long. It has a 16" x 18" mounting surface for steering and gauges.
30"H x 23"W x 22"D Measurements include flange
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
This product is great work boat size because it is tall and narrow.
30"H x 23"W x 22"D
Additional measurements:
- 16 inch x 18 inch section that holds the steering and controls
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
25 inch Center Console 01
Our 25 inch Center Console 01 from Boaters Catalog has large rounded corners and is perfect for boats 13' to 13' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 23"W x 23"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
Windlass Service Spares and Parts
Windlass Service Spares and Parts
We have access to parts for Lewmar, Horizon, Sprint, Simpson Lawrence, James Neilssen, Maxwell, and Quick. Many of the older uiits have no parts available but we won't know until we check with our US supplier. Some are available from Scotland, but they are more expensive and take a longer time to acquire.
If you need parts or service on your windlass, call us at 800-745-0765, Monday - Friday 9 am - 4 pm EST.
Pull Up Cleat 209
Our Pull Up Cleat 209 from Boaters Catalog have a flat design that keeps you gunwales and bow clean looking. They are ideal for avoiding trip hazards on your boat when they are not in use.
- Sealed base eliminates the need for a waterproofing cup, water can be drained through a fitting at the bottom of the unit.
- Can be converted to a lifting cleat by inserting a connecting rod in the base of the unit and attaching the rod to the bow eye.
- Made of marine grade 316 stainless steel.
- Available in four sizes: 4 1/2", 6", 8" & 10".
- 10" version is available in both through bolt (visible screw holes) and stud-mount (no visible screw holes).
- Each cleat is shipped with a backing plate which also serves as the cut-out template..
- Screws are not included
209-4 requires quantity (4) 3/16" screws
209-6 requires quantity (4) 1/4" screws
209-8 requires quantity (4) 1/4" screws
209-10 requires quantity (4) 5/16" screws
Bow Pulpit 45 Inch with hole
Our top quality fiberglass Bow Pulpit 45 Inch with hole from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
- This product has a built in non-skid surface.
- It keeps the anchor away from the deck of boat and the section that is narrow, where the shank of the anchor goes, is 4 3/4"L x 3"W.
- The front bow opening is 4 1/8" and back of opening is 5 1/4"W x 8 1/2"L.
- Weight appx. 42 pounds
- Approximate thickness is 3 inches.
- 12"Wide x 45"Long
NOTE: These are semi-custom items and are not in stock on the shelf. They are usually built and in the mold ready to take out, finish, and ship. Depending on the number of orders for the pulpits and other fiberglass items, shipping could take 1-2 weeks.
This item can not be shipped outside the Continental United States.
Freight will be quoted after your order or you can call 800-745-0765.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.https://boaterscatalog.com/nbcat/product-category/explore_product/customize/
48 inch Center Console
Our 48 inch Center Console from Boaters Catalog has large rounded corners and is perfect for boats 16' to 18' long. This product is great work boat size because it is tall and narrow.
48"H x 24"W x 24"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
This product is great work boat size because it is tall and narrow.
48"H x 24"W x 24"D
Additional measurements
- 22 inch x 14 inch section that holds the steering and controls
- 21 inch x 10 1/2 inch part that angles down from the top facing the driver
- 21 inch x 7 inch, the flat part on the top
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.