Product Information
Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates$288.00 – $728.00
The CMC Manual Jack Plates from Boaters Catalog has comparable design and construction features as the hydraulic lift without the convenience of automated adjustment.
If you desire engine performance enhancement, but don’t have the budget for our hydraulic unit then the ML-65 may be exactly what you are looking for. Our manual units provide similar benefits to the hydraulic units. However, since you cannot raise or lower the engine as you are moving you will not receive the same performance enhancements associated with a hydraulic unit.
The 4 and 5-1/2 inch set back plates are rated for V-6 and smaller motors. They are NOT designed for V-8 or racing applications.
Manual ML-65HD, item#65512 rated for V8 400HP outboards or smaller.
(See description below for transom washer plates and wedges.)
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Description
Manual Jack Plates
One Piece Manual Features:
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• Centrally located adjustment screw for positive alignment
• 5 1/2″ and 10” Set Backs from Transom are available
• 5″ Vertical Adjustment
• Designed to fit standard B.I.A. bolt pattern
• Aluminum models rated for up to V6 outboards
Two Piece Manual Features
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• 4” and 5 1/2″ Set Backs from Transom are available
• 5” of slot adjustment at the motor mounting bracket
• 1 ½” of adjustment at the transom bracket.
Manual ML-65HD, item#65512 rated for V8 400HP outboards
Transom Support Plates / Transom Washer Plates
Made of strong 3/8″ 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts “biting” into transoms and can more evenly distribute loads on high performance engines.
Hole centers: Top Plate – 12 7/8″ Bottom Plate – 9 7/8″
Transom Wedges and Setback Spacers (Item #20122)
These 2 degree wedges are designed to give extra positive or negative trim.
Features:
Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed
Unique design of the CMC Transom Wedges allows you to also use them as set back spacers
Simply stack and invert 2, 4, and 6 sets (sold in sets of two)
Fit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt pattern
Made of strong 6061 T6 alloy aluminum (not cast aluminum)
- 65012- ML-65-5 1/2 with 5 1/2 inch set back - DIM. 18 1/8"W x 15 1/5"H Weight 32#
- 61012 - ML-65-10 with 10 inch set back - DIM. 18 1/8"W x 15 1/2"H Weight 43#
- 55012 - 2 Piece Manual w/5-1/2" setback 18 1/8" x 15 1/2"H (mounted) Weight 23#
- 40012 - 2 Piece Manual w/4" setback - DIM. 18 1/8"W x 15 1/2"H (mounted) Weight 20#
Related Products
Bow Pulpit 33 Inch
This top quality Bow Pulpit 33 Inch from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
33in long x 11in wide at the bow x 3in thick
- Tapers to approximately 7 1/2 wide at the end
- Weight 18 pounds
- Approximate thickness is 2 1/5 to 2 3/4 inches.
This item can not be shipped outside the Continental United States.
There is an 11 week lead time for all fiberglass products right now.
See more of our quality boat products here.
35 inch Console with Front Seat
Our 35 inch Console with Front Seat from Boaters Catalog has an overall height of 35" and an over all length including flange is 43 1/2". Rear including flange is 38" and front including flange is 32". This console is perfect for boats 21' to 25' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
Front seat is so your passenger can safely sit on the center line of the boat.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
35"H x 36"W x 43-1/2"D
Additional measurements:
- Rear width including flange 38"
- Front width including flange 32"
- Seat approx 15-1/2" high from deck
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
LED Bow Light
Our LED Bow Light from Boaters Catalog is the perfect addition to the bow of your boat to keep it sleek looking and a non trip hazard area.
Navigation Light - LED Bow Light - 210-M
FEATURES:
USCG approved 2 nautical miles.
The only Pop-Up® LED light on the market.
Keeps deck free of protruding lights, folds down flush with deck when not in use.
Made of marine grade 316 stainless steel.
An optional plastic cup prevents unwanted water runoff below deck.
INSTALLATION Drill a 3 1/2" diameter hole using a hole saw. Fasten with three #10 screws (not included).
DIMENSIONS Above Deck Length = 4.43" Width (at the widest point)= 4.0" Height = 2.15"
Below Deck Depth = 2.65"
Proper maintenance consists of rinsing with fresh water regularly, and following each exposure to salt water. Stainless steel surfaces should be periodically wiped with a clean, soft cloth. Plastic surfaces may be cleaned with a mild, non-abrasive detergent solution, then rinsed with fresh water as necessary.
See more of our quality boat accessories here.
Bench Seat
Our Bench Seat from Boaters Catalog is a super comfortable fiberglass bench seat that can be used for a boat, pool area, patio, or on a dock. It seats 2 adults or 3 children comfortably. It has an Ultra-violet resistant white gelcoat. The seat from top to bottom is 16".
- 43"L x 30"D x 26"H
There is an 11 week lead time on our fiberglass products at this time.
53 inch High Center Console
Our 53 inch High Center Console from Boaters Catalog has enough space to flush mount all your electronics. Dash mounting area for controls and steering is 34" x 16" and has an average fiberglass thickness of 3/8".
Base measurements including flange are 38" x 38" and height is 53".
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
53"H x 38"W x 38"D
This console is perfect for single or twin engine boats.
Freight will be quoted shortly after your order or you may call 800-745-0765 for a quote.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
Deluxe Step Box with Storage 2
Our Deluxe Step Box with Storage 2 has sleek rounded edges, built in non skid surface on top of the steps and Euro-style chrome brass handles.
W 22" x H 14" x D 17.5"
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products
Pet Dining Mats
Our Custom Embroidered Pet Dining Mats from Boaters Catalog are Made of MARINE GRADE plush carpet that is antimicrobial, with a non-skid rubber backing. All edges are beautifully finished with poly binding. We provide custom embroidery to match. We offer your custom pet mat in 4 sizes based on your pets' size. Our mats are easy to clean and our bowls are Stainless Steel and dishwasher safe, 2 stainless steel bowls per Pet Feeding Set.
Sizes are:
- Small- 12x20 mat with 2 ea. 8oz bowls(good for cats)
- Medium- 17x24 mat with 2 ea. 16oz bowls
- Large- 17x27 mat with 2 ea. 32oz bowls
- Xtra-Large- 18x30 mat with 2 ea. 64oz bowls
- Included-Add your personalization just for your pet!
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Pet Feeding Mat is customized with your embroidered pet name or other text, adding that personal touch.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing.
Our premium Marine Carpet Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 10-14 business days from the time of your order until it is shipped.
See our color charts below as you choose your carpet options.
See our other quality boat and dock products here.
Half Moon Boarding Mat
Our Custom Embroidered Half Moon Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your deck from marks and scratches while creating a safe way to board your boat. Our mats are seen as door mats around homes as well as on the docks and boats around the country.
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Boarding Mat can be customized with your embroidered boat name or other text, adding that personal touch.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing.
Our premium Marine Carpet Boarding Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
If you want more customization just call us at 800-745-0765/
See our other quality boat and dock products here.
25 inch Center Console 01
Our 25 inch Center Console 01 from Boaters Catalog has large rounded corners and is perfect for boats 13' to 13' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 23"W x 23"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.