Orca Heavy Duty Performance Fin
The Orca Heavy Duty Performance Fin from Boaters Catalog triples the effective rudder area providing a tighter turn radius and sharp crisp directional control at any speed. The larger surface area of the Orca Heavy Duty Performance Fin blocks cavitation better than hydrofoils while adding the benefit of enhanced slow speed maneuvering and heading control. The Orca Heavy Duty Performance Fin installs in minutes without drilling using the 45M-Clamp kit or bolt directly to the cavitation plate using included hardware.
The Orca fin is usually mounted with the fins down but may be installed fins up without modification if you desire less aggressive control. Used and tested on fishing boats, runabouts, pontoon boats, cruisers, ski boats and bass boats over 250 HP.
Orca Performance Fin
The Orca Performance Fin from Boaters Catalog triples the effective rudder area providing a tighter turn radius and sharp crisp directional control at any speed. The larger surface area of the Orca Performance Fin blocks cavitation better than hydrofoils while adding the benefit of enhanced slow speed maneuvering and heading control. The Orca-Performance Fin installs in minutes without drilling using the 45M-Clamp kit or bolt directly to the cavitation plate using included hardware.
The Orca fin is usually mounted with the fins down but may be installed fins up without modification if you desire less aggressive control. Used and tested on fishing boats, runabouts, pontoon boats, cruisers, ski boats and bass boats (over 80 HP) since 2002.
The New Orca Heavy Duty Fin for outboards over 250 HP is now available, click here.
Static Jack Plate 5 inch
The CMC Static Jack Plate 5 inch vertical outboard motor extension allows the motor to be mounted 5 inches higher than the standard mounting height on the transom.
It is a must for easy conversion from prop drive to jet drive.
Another application includes mounting the 5 inch vertical extension on a hydraulic jack plate to raise the motor higher on shallow running boats that are equipped with tunnel extensions.
Constructed of Extruded 6061-T6 Aluminum alloy. (#50012) They are 5” wide and 20-1/2” long. It is rated for 300 HP and smaller motors.
Hydraulic Jack Plate for 400HP
The CMC HD Hydraulic Jack Plate PL-65HD Power-Lift from Boaters Catalog is designed for 400 HP outboard motors. The PL-65HD is made of 6061 T6 aluminum alloy extrusions and fastened with stainless steel fasteners for maximum strength and durability. The structure incorporates a patented roller design providing less friction, longer wear, less maintenance and virtually eliminates any chance of binding.
The self-contained and water proof electric hydraulic power unit and cylinder is embodied into one actuator inside the structure of the Power-Lift and includes its own fluid reservoir. Providing a lifting capacity of 7853 lbs of thrust, it has no problem lifting a 400 HP motor at full speed.
The CMC HD Hydraulic Jack Plate is made of 100% non-ferrous material which makes it more impervious to salt and fresh water. This design eliminates the need to install a hydraulic tank, motor, pump and hoses inside the boat saving the boat room where needed. It comes full of fluid, tested and ready for operation.
(See below for a description of transom wedges and washer plates.)
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
See all our quality CMC products for your outboard motor here.
Hydrofoil Fin
Our Hydrofoil Fin from Boaters Catalog will add directional control and stability that you've been missing. Uncle Norm’s Hydrofoil Fin triples the effective rudder area giving you powerful directional control at very high speeds and adds crisp, responsiveness at any speed. These fins do not add drag at high speeds but are a great help maneuvering at slow speeds and during docking or trailering the boat. Fins on hydrofoils are a great help tracking on course in windy conditions or in current.
Includes 2 fins that bolt onto your hydrofoil fin.
Hydrofoil is not included.
Manual Jack Plates
The CMC Manual Jack Plates from Boaters Catalog has comparable design and construction features as the hydraulic lift without the convenience of automated adjustment.
If you desire engine performance enhancement, but don’t have the budget for our hydraulic unit then the ML-65 may be exactly what you are looking for. Our manual units provide similar benefits to the hydraulic units. However, since you cannot raise or lower the engine as you are moving you will not receive the same performance enhancements associated with a hydraulic unit.
The 4 and 5-1/2 inch set back plates are rated for V-6 and smaller motors. They are NOT designed for V-8 or racing applications.
Manual ML-65HD, item#65512 rated for V8 400HP outboards or smaller.
(See description below for transom washer plates and wedges.)
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Break Away Mount
Our CMC BA-130 Break Away Mount from Boaters Catalog is designed for duck hunters and/or fisherman that use their boat in shallow stumpy areas. It allows small boats and motors to slide over submerged logs or debris at low speeds to get to a downed bird or your favorite fishing hole.
The BA-130 is rated for outboard motors up to a maximum of 130 H.P.
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
PT35 Tilt and Trim
Our PT35 Tilt and Trim is a lighter, more compact Tilt and Trim unit manufactured for 35 horsepower motors and smaller(Down to 2 H.P.). This unit is 11-1/2 inches wide and weighs only 24 lbs! The PT-35 utilizes the same hydraulic actuator as the PT-130 and gives you all the same benefits. This unit easily adapts to bolt-on motors and clamp-on motors (within the 11 inch frame) without the need of an adapter.
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
PT130 Tilt and Trim
The CMC PT-130 Tilt and Trim for up to 130 HP from Boaters Catalog allows you to tuck your motor in to get your boat on plane smoother and faster. When you’re underway, you can change the angle of your motor to obtain the best performance for your load and water conditions. It gives you a more stable ride, increases top end speed, allows more prop clearance, and better fuel economy.
Electric Hydraulic Tilt & Trim
You Get Power Tilt & Trim, Better Boat Handling, More Speed, Lower Fuel Consumption and No More Back Strain!
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
See all our quality CMC products for your outboard here.
High Speed Hydraulic Power Lift
This dependable, self contained, and water proof High Speed Hydraulic Power Lift from Boaters Catalog has a maximum lifting capacity of 7,853 pounds of thrust. With the CMC High Speed Hydraulic Power-Lift you will have no problem lifting even a V-6 300 hp max. motor at full throttle. The hydraulic actuator is mounted inside the structure of the Power-Lift, yet it is fully accessible without removing the engine. There are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks.
The hydraulic actuator is completely self-contained with its own fluid reservoir (eliminates the need for hydraulic tank and hoses inside the boat). It contains a permanent magnet motor for more power and constant torque. The cylinder within the actuator has twice the lifting capacity than other transom jacks on the market. It contains a no-leak seal and wiper that keeps dirt and water out of the working parts. The system is made of 100% non-ferrous material which makes it impervious to saltwater and freshwater.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.