Important Information...
Online Policies
International Sales
Shipping and Returns
Your Privacy Matters
Talk to Us!
Product Information
Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack PlatesPrice range: $288.00 through $728.00
The CMC Manual Jack Plates from Boaters Catalog has comparable design and construction features as the hydraulic 
lift without the convenience of automated adjustment.
If you desire engine performance enhancement, but don’t have the budget for our hydraulic unit then the ML-65 may be exactly what you are looking for. Our manual units provide similar benefits to the hydraulic units. However, since you cannot raise or lower the engine as you are moving you will not receive the same performance enhancements associated with a hydraulic unit.
The 4 and 5-1/2 inch set back plates are rated for V-6 and smaller motors. They are NOT designed for V-8 or racing applications.
Manual ML-65HD, item#65512 rated for V8 400HP outboards or smaller.
(See description below for transom washer plates and wedges.)
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Description
More Information
Description
Manual Jack Plates
One Piece Manual Features:
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• Centrally located adjustment screw for positive alignment
• 5 1/2″ and 10” Set Backs from Transom are available
• 5″ Vertical Adjustment
• Designed to fit standard B.I.A. bolt pattern
• Aluminum models rated for up to V6 outboards
Two Piece Manual Features
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• 4” and 5 1/2″ Set Backs from Transom are available
• 5” of slot adjustment at the motor mounting bracket
• 1 ½” of adjustment at the transom bracket.
Manual ML-65HD, item#65512 rated for V8 400HP outboards
Transom Support Plates / Transom Washer Plates
Made of strong 3/8″ 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts “biting” into transoms and can more evenly distribute loads on high performance engines.
Hole centers: Top Plate – 12 7/8″ Bottom Plate – 9 7/8″
Transom Wedges and Setback Spacers (Item #20122)
These 2 degree wedges are designed to give extra positive or negative trim.
Features:
Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed
Unique design of the CMC Transom Wedges allows you to also use them as set back spacers
Simply stack and invert 2, 4, and 6 sets (sold in sets of two)
Fit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt pattern
Made of strong 6061 T6 alloy aluminum (not cast aluminum)
- 65012- ML-65-5 1/2 with 5 1/2 inch set back - DIM. 18 1/8"W x 15 1/5"H Weight 32#
- 61012 - ML-65-10 with 10 inch set back - DIM. 18 1/8"W x 15 1/2"H Weight 43#
- 55012 - 2 Piece Manual w/5-1/2" setback 18 1/8" x 15 1/2"H (mounted) Weight 23#
- 40012 - 2 Piece Manual w/4" setback - DIM. 18 1/8"W x 15 1/2"H (mounted) Weight 20#
Related Products
Quick View
Bow Pulpit 60 Inch
Maintain or improve your boat's ground tackle, Bow Pulpits, Customize Your Vessel, Improve the hardware on your boat
Our top quality fiberglass Bow Pulpit 60 Inch from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations. 
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
NOTE: These are semi-custom items and are not in stock on the shelf. They are usually built and in the mold ready to take out, finish, and ship. Depending on the number of orders for the pulpits and other fiberglass items, shipping could take 1-2 weeks. 3.75" high x 17" wide x 60" long
- Weight appx. 46 pounds
- Reinforced with 5/8" marine grade plywood
- Built in non-skid surface and rounded corners
This item can not be shipped outside the Continental United States.
Freight will be quoted after your order or you can call 800-745-0765.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
Quick View
Fiberglass Live Wells
Improve or add to your bait well system, Bait wells, live wells, and accessories, Customize Your Vessel
These high quality fiberglass tanks are gel coated inside and out with a white finish outside and a blue finish inside to help keep the bait calm. The Standard tanks have a white lid for easy dipping of bait.
All our wells have no holes for water in or out so they can be custom installed on your boat with the plumbing at the correct height. They do include a drain at the bottom of the tank.
Our Heavy Water tanks are built with additional lay-ups of fiberglass and have a square clear top with stainless steel hardware.
- 30 gal. 20.5" H x 19.5" diameter
- 40 gal. 21" H x 23" diameter
- 50 gal. 24" H x 26" diameter
- 80 gal. 29.5"H x 29"W
- 100 gal. 33" H x 33.5" diameter
There is an 11 week lead time on fiberglass items at this time.
This item cannot be shipped outside the Continental United States. This item can not ship via UPS and freight will be quoted by e-mail or telephone at time of purchase. The shopping cart will not add freight to your order. We will call you with your shipping costs after your order has been received.
close
You may call us at 800-745-0765 for a quote.
Price range: $330.00 through $870.00
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
15 Inch Pull Up Cleat
Our 15 Inch Pull Up Cleat from Boaters Catalog is THE LARGEST FLUSH-MOUNTED CLEAT AVAILABLE! Its the perfect cleat to keep the gunwale and bow of your vessel clean and sleek looking at the same time avoiding a trip hazard.
FEATURES:
- The largest flush-mounted cleat available!
- Made of marine grade 316 stainless steel.
- Available in both stud mount and through-bolt versions.
- Stud length is 4" on part # 115-15-S.
- Each cleat is supplied with a waterproofing cup(shown).
INSTALLATION
- Each cleat is shipped with a backing plate which also serves as the cut-out template.
- Fasten with four 3/8" diameter screws (not included),weight = 16 pounds each.
Available with visible screw holes as PN 115-15 (load of 61,000 pounds), or with studs on the underside of base as PN 115-15-S (load of 31,000 pounds).
Shipping weight 19#
Proper maintenance consists of rinsing with fresh water regularly, and following each exposure to salt water. Stainless steel surfaces should be periodically wiped with a clean, soft cloth. Plastic surfaces may be cleaned with a mild, non-abrasive detergent solution, then rinsed with fresh water as necessary.
$920.00
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Windlass Service Spares and Parts
Windlass Service Spares and Parts
We have access to parts for Lewmar, Horizon, Sprint, Simpson Lawrence, James Neilssen, Maxwell, and Quick. Many of the older uiits have no parts available but we won't know until we check with our US supplier. Some are available from Scotland, but they are more expensive and take a longer time to acquire.
If you need parts or service on your windlass, call us at 800-745-0765, Monday - Friday 9 am - 4 pm EST.
Quick View
Bench Seat
Our Bench Seat from Boaters Catalog is a super comfortable fiberglass bench seat that can be used for a boat, pool area, patio, or on a dock. It seats 2 adults or 3 children comfortably. It has an Ultra-violet resistant white gelcoat. The seat from top to bottom is 16".
- 43"L x 30"D x 26"H
There is an 11 week lead time on our fiberglass products at this time.
Quick View
Anchor Line and Chain
Captain Charlie's™ Anchor Line and Chain from Boaters Catalog is custom fabricated to meet your specific needs. We can custom cut any length of line or line and chain combination that you want in any sizes that you need.
The combinations that you see here are the most popular lengths and sizes that are appropriate for many electric windlasses. Please remember that not all windlasses use the same size and type of line or the same chain. Most will only pull the type of rode they are designed for. The 8 Brait line is compatible with both Lewmar and Powerwinch and will take up much less room in your anchor locker.
If you want something other than what you see here, please call 800-745-0765 or e-mail us with your specifications and we will be glad to call you back with a quote.
Freight will not be figured by the shopping cart. We will contact you when your order is received with your freight quote.close
Price range: $182.00 through $879.80
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
30 inch Center Console
Our 30 inch Center Console from Boaters Catalog has large rounded corners and is perfect for boats 15' to 18' long. It has a 16" x 18" mounting surface for steering and gauges.
30"H x 23"W x 22"D Measurements include flange
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
This product is great work boat size because it is tall and narrow.
30"H x 23"W x 22"D
Additional measurements:
- 16 inch x 18 inch section that holds the steering and controls
*NOTE: There is an 4-6 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Quick View
Bow Pulpit 45 Inch with hole
Improve the hardware on your boat, Bow Pulpits, Customize Your Vessel, Maintain or improve your boat's ground tackle
Our top quality fiberglass Bow Pulpit 45 Inch with hole from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
- This product has a built in non-skid surface.
- It keeps the anchor away from the deck of boat and the section that is narrow, where the shank of the anchor goes, is 4 3/4"L x 3"W.
- The front bow opening is 4 1/8" and back of opening is 5 1/4"W x 8 1/2"L.
- Weight appx. 42 pounds
- Approximate thickness is 3 inches.
- 12"Wide x 45"Long
NOTE: These are semi-custom items and are not in stock on the shelf. They are usually built and in the mold ready to take out, finish, and ship. Depending on the number of orders for the pulpits and other fiberglass items, shipping could take 1-2 weeks.
This item can not be shipped outside the Continental United States.
Freight will be quoted after your order or you can call 800-745-0765.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.https://boaterscatalog.com/nbcat/product-category/explore_product/customize/
Quick View
Single Cockpit Step with Storage
Maintain or improve your dock, Boarding Steps and Ladders, Customize Your Vessel, Improve the hardware on your boat
Our Single Cockpit Step with Storage has sleek rounded edges, built in non skid surface on top of the steps and chrome brass handles. This step box can hold up to 250 lbs. and has Ultra-violet resistant white gelcoat.
L 20" x D 16" x H 13"
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products at this time.
Quick View
53 inch High Center Console
Our 53 inch High Center Console from Boaters Catalog has enough space to flush mount all your electronics. Dash mounting area for controls and steering is 34" x 16" and has an average fiberglass thickness of 3/8".
Base measurements including flange are 38" x 38" and height is 53".
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
53"H x 38"W x 38"D
This console is perfect for single or twin engine boats.
Freight will be quoted shortly after your order or you may call 800-745-0765 for a quote.
There is an 4-6 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
