Total:
$2,143.50
$785.00
Our PT35 Tilt and Trim is a lighter, more compact Tilt and Trim unit manufactured for 35 horsepower motors and 
smaller(Down to 2 H.P.). This unit is 11-1/2 inches wide and weighs only 24 lbs! The PT-35 utilizes the same hydraulic actuator as the PT-130 and gives you all the same benefits. This unit easily adapts to bolt-on motors and clamp-on motors (within the 11 inch frame) without the need of an adapter.
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
You Get Power Tilt & Trim, Better Boat Handling, More Speed, Lower Fuel Consumption and No More Back Strain!
PT-35 FEATURES:
• Rated for 35 horse power and Smaller Motors.
• 5 1/2″ Set Back to Enhance Boat Stability and Performance.
• 84° of Trim and Tilt.
• 1/4″ 6061 T6 Extruded Aluminum Construction with Stainless Steel Fasteners.
• Electric Hydraulic Actuator Rated at 7853 lbs. of Thrust!
• Accommodates Clamp-on or Bolt-on Motors Without the Need of an Adapter.
• Weighs Only 24 Pounds!
Note: The inside dimension of the motor mounting area of the PT-35 is 11 inches. Before ordering, please make sure that the maximum width of the clamp mounting feet and/or mounting bolts of the motor that must fit into this area does not exceed this 11 inch limit. Mounting bolts are not included with the PT-35.
Quick View
Our 15 Inch Pull Up Cleat from Boaters Catalog is THE LARGEST FLUSH-MOUNTED CLEAT AVAILABLE! Its the perfect cleat to keep the gunwale and bow of your vessel clean and sleek looking at the same time avoiding a trip hazard.
FEATURES:
INSTALLATION
Available with visible screw holes as PN 115-15 (load of 61,000 pounds), or with studs on the underside of base as PN 115-15-S (load of 31,000 pounds).
Shipping weight 19#
Proper maintenance consists of rinsing with fresh water regularly, and following each exposure to salt water. Stainless steel surfaces should be periodically wiped with a clean, soft cloth. Plastic surfaces may be cleaned with a mild, non-abrasive detergent solution, then rinsed with fresh water as necessary.
Quick View
Our Custom Embroidered Gunwale Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your gunwale from marks and scratches 
while creating a safe way to board your boat.
(our mat image shows the 20" width of the mat as it lays over the gunwale)
If you don't want the name of your boat on the mat we can put "Welcome Aboard" or "Boat Shoes Only" or any short phrase of your choosing.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
Quick View
Our Custom Embroidered Pet Dining Mats from Boaters Catalog are Made of MARINE GRADE plush carpet that is antimicrobial, with a non-skid rubber backing. All edges are beautifully finished with poly binding. We provide custom embroidery to match. We offer your custom pet mat in 4 sizes based on your pets' size. Our mats are easy to clean and our bowls are Stainless Steel and dishwasher safe, 2 stainless steel bowls per Pet Feeding Set.
Sizes are:
Our premium Marine Carpet Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 10-14 business days from the time of your order until it is shipped.
See our color charts below as you choose your carpet options.
See our other quality boat and dock products here.
Quick View
Our 25 inch Center Console from Boaters Catalog has an average fiberglass thickness of 1/4"-3/8". Also the dash is reinforced with 11 mm Nida Core. This console is perfect for small skiffs 13'-16' long.
25"H x 21"W x 16"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 21"W x 16"D
*NOTE: There is an 4-6 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
Quick View
Windlass Service Spares and Parts
We have access to parts for Lewmar, Horizon, Sprint, Simpson Lawrence, James Neilssen, Maxwell, and Quick. Many of the older uiits have no parts available but we won't know until we check with our US supplier. Some are available from Scotland, but they are more expensive and take a longer time to acquire.
If you need parts or service on your windlass, call us at 800-745-0765, Monday - Friday 9 am - 4 pm EST.
Quick View
Our 35 inch Console with Front Seat from Boaters Catalog has an overall height of 35" and an over all length including flange is 43 1/2". Rear including flange is 38" and front including flange is 32". This console is perfect for boats 21' to 25' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
Front seat is so your passenger can safely sit on the center line of the boat.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
35"H x 36"W x 43-1/2"D
Additional measurements:
There is an 4-6 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Quick View
Captain Charlie's™ Anchor Line and Chain from Boaters Catalog is custom fabricated to meet your specific needs. We can custom cut any length of line or line and chain combination that you want in any sizes that you need.
The combinations that you see here are the most popular lengths and sizes that are appropriate for many electric windlasses. Please remember that not all windlasses use the same size and type of line or the same chain. Most will only pull the type of rode they are designed for. The 8 Brait line is compatible with both Lewmar and Powerwinch and will take up much less room in your anchor locker.
If you want something other than what you see here, please call 800-745-0765 or e-mail us with your specifications and we will be glad to call you back with a quote.
Freight will not be figured by the shopping cart. We will contact you when your order is received with your freight quote.close
Quick View
Our 37 inch High Center Console from Boaters Catalog has a 25" x 16" mounting surface for steering and gauges and has large rounded corners. It is perfect for boats 18' to 24'.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
37"H x 31"W x 31"D
There is an 4-6 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Quick View
Our 29 inch Center Console with Seat from Boaters Catalog has an average fiberglass thickness of 3/8" and has a seat molded into the console. This product is perfect for boats 19' to 24' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
There is an 4-6 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Quick View
Our Custom Embroidered Rectangular Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your deck from marks and scratches while creating a safe way to board your boat.
Our premium Marine Carpet Boarding Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
Choose the colors and font choices from the charts below and mark them in the drop down boxes.
Don't forget, our mats are great for home use as well as on the dock and the boat!
See our other quality boat and dock products here.
Important Information...
Online Policies
International Sales
Shipping and Returns
Your Privacy Matters
Talk to Us!
100% Satisfaction Guaranteed!
Boater’s Catalog
6240 105th Terrace N.
Pinellas Park, FL 33782
Tel: (800) 745-0765
