Product Information
Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates$1,460.00 – $1,684.00
The CMC HD Hydraulic Jack Plate PL-65HD Power-Lift from Boaters Catalog is designed for 400 HP outboard motors. The PL-65HD is made of 6061 T6 aluminum alloy extrusions and fastened with stainless steel fasteners for maximum strength and durability. The structure incorporates a patented roller design providing less friction, longer wear, less maintenance and virtually eliminates any chance of binding.
The self-contained and water proof electric hydraulic power unit and cylinder is embodied into one actuator inside the structure of the Power-Lift and includes its own fluid reservoir. Providing a lifting capacity of 7853 lbs of thrust, it has no problem lifting a 400 HP motor at full speed.
The CMC HD Hydraulic Jack Plate is made of 100% non-ferrous material which makes it more impervious to salt and fresh water. This design eliminates the need to install a hydraulic tank, motor, pump and hoses inside the boat saving the boat room where needed. It comes full of fluid, tested and ready for operation.
(See below for a description of transom wedges and washer plates.)
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
See all our quality CMC products for your outboard motor here.
Description
CMC HD Hydraulic Jack Plate for 400 HP
Transom Support Plates / Transom Washer Plates
Made of strong 3/8″ 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts “biting” into transoms and can more evenly distribute loads on high performance engines.
Hole centers: Top Plate – 12 7/8″ Bottom Plate – 9 7/8″
Transom Wedges and Setback Spacers (Item #20122)
These 2 degree wedges are designed to give extra positive or negative trim.
Features:
- Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed
- Unique design of the CMC Transom Wedges allows you to also use them as set back spacers
- Simply stack and invert 2, 4, and 6 sets (sold in sets of two)
- Fit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt pattern
- Made of strong 6061 T6 alloy aluminum (not cast aluminum)
Related Products
Bow Pulpit 60 Inch
Our top quality fiberglass Bow Pulpit 60 Inch from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
NOTE: These are semi-custom items and are not in stock on the shelf. They are usually built and in the mold ready to take out, finish, and ship. Depending on the number of orders for the pulpits and other fiberglass items, shipping could take 1-2 weeks. 3.75" high x 17" wide x 60" long
- Weight appx. 46 pounds
- Reinforced with 5/8" marine grade plywood
- Built in non-skid surface and rounded corners
This item can not be shipped outside the Continental United States.
Freight will be quoted after your order or you can call 800-745-0765.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
30 inch Center Console
Our 30 inch Center Console from Boaters Catalog has large rounded corners and is perfect for boats 15' to 18' long. It has a 16" x 18" mounting surface for steering and gauges.
30"H x 23"W x 22"D Measurements include flange
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
This product is great work boat size because it is tall and narrow.
30"H x 23"W x 22"D
Additional measurements:
- 16 inch x 18 inch section that holds the steering and controls
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
15 Inch Pull Up Cleat
Our 15 Inch Pull Up Cleat from Boaters Catalog is THE LARGEST FLUSH-MOUNTED CLEAT AVAILABLE! Its the perfect cleat to keep the gunwale and bow of your vessel clean and sleek looking at the same time avoiding a trip hazard.
FEATURES:
- The largest flush-mounted cleat available!
- Made of marine grade 316 stainless steel.
- Available in both stud mount and through-bolt versions.
- Stud length is 4" on part # 115-15-S.
- Each cleat is supplied with a waterproofing cup(shown).
INSTALLATION
- Each cleat is shipped with a backing plate which also serves as the cut-out template.
- Fasten with four 3/8" diameter screws (not included),weight = 16 pounds each.
Available with visible screw holes as PN 115-15 (load of 61,000 pounds), or with studs on the underside of base as PN 115-15-S (load of 31,000 pounds).
Shipping weight 19#
Proper maintenance consists of rinsing with fresh water regularly, and following each exposure to salt water. Stainless steel surfaces should be periodically wiped with a clean, soft cloth. Plastic surfaces may be cleaned with a mild, non-abrasive detergent solution, then rinsed with fresh water as necessary.
Bow Pulpit 33 Inch
This top quality Bow Pulpit 33 Inch from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
33in long x 11in wide at the bow x 3in thick
- Tapers to approximately 7 1/2 wide at the end
- Weight 18 pounds
- Approximate thickness is 2 1/5 to 2 3/4 inches.
This item can not be shipped outside the Continental United States.
There is an 11 week lead time for all fiberglass products right now.
See more of our quality boat products here.
37 inch High Center Console
Our 37 inch High Center Console from Boaters Catalog has a 25" x 16" mounting surface for steering and gauges and has large rounded corners. It is perfect for boats 18' to 24'.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
37"H x 31"W x 31"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Single Cockpit Step
W 21-1/4" x H 12" x D 17 1/4"
Our Single Cockpit Step from Boaters Catalog has sleek rounded edges, built in non skid surface on top of the steps and chrome brass handles. This step box can hold up to 250 lbs. and has Ultra-violet resistant white gelcoat.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products at this time.
Deluxe Step Box with Storage 2
Our Deluxe Step Box with Storage 2 has sleek rounded edges, built in non skid surface on top of the steps and Euro-style chrome brass handles.
W 22" x H 14" x D 17.5"
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products
Deluxe Step Box with Storage
Our Deluxe Step Box with Storage has sleek rounded edges, built-in non skid surface on top of the steps, and Euro-style chrome brass handles.
W 22" x H 12.75" x D 17.5"
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
Rectangular Boarding Mat
Our Custom Embroidered Rectangular Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your deck from marks and scratches while creating a safe way to board your boat.
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Boarding Mat can be customized with your embroidered boat name or other text, adding that personal touch.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing, Our Gunnel Mat is larger than most- check your sizes before purchasing! Total size is shown as a choice and the custom embroidery covers the width of the mat.
Our premium Marine Carpet Boarding Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
Choose the colors and font choices from the charts below and mark them in the drop down boxes.
Don't forget, our mats are great for home use as well as on the dock and the boat!
See our other quality boat and dock products here.
Half Moon Boarding Mat
Our Custom Embroidered Half Moon Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your deck from marks and scratches while creating a safe way to board your boat. Our mats are seen as door mats around homes as well as on the docks and boats around the country.
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Boarding Mat can be customized with your embroidered boat name or other text, adding that personal touch.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing.
Our premium Marine Carpet Boarding Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
If you want more customization just call us at 800-745-0765/
See our other quality boat and dock products here.