Product Information
Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates$288.00 – $728.00
The CMC Manual Jack Plates from Boaters Catalog has comparable design and construction features as the hydraulic lift without the convenience of automated adjustment.
If you desire engine performance enhancement, but don’t have the budget for our hydraulic unit then the ML-65 may be exactly what you are looking for. Our manual units provide similar benefits to the hydraulic units. However, since you cannot raise or lower the engine as you are moving you will not receive the same performance enhancements associated with a hydraulic unit.
The 4 and 5-1/2 inch set back plates are rated for V-6 and smaller motors. They are NOT designed for V-8 or racing applications.
Manual ML-65HD, item#65512 rated for V8 400HP outboards or smaller.
(See description below for transom washer plates and wedges.)
See all our quality CMC products for your outboard here.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Description
Manual Jack Plates
One Piece Manual Features:
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• Centrally located adjustment screw for positive alignment
• 5 1/2″ and 10” Set Backs from Transom are available
• 5″ Vertical Adjustment
• Designed to fit standard B.I.A. bolt pattern
• Aluminum models rated for up to V6 outboards
Two Piece Manual Features
• Made of 6061 T6 extruded aluminum alloy
• Stainless steel fasteners for maximum strength and durability
• 4” and 5 1/2″ Set Backs from Transom are available
• 5” of slot adjustment at the motor mounting bracket
• 1 ½” of adjustment at the transom bracket.
Manual ML-65HD, item#65512 rated for V8 400HP outboards
Transom Support Plates / Transom Washer Plates
Made of strong 3/8″ 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts “biting” into transoms and can more evenly distribute loads on high performance engines.
Hole centers: Top Plate – 12 7/8″ Bottom Plate – 9 7/8″
Transom Wedges and Setback Spacers (Item #20122)
These 2 degree wedges are designed to give extra positive or negative trim.
Features:
Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed
Unique design of the CMC Transom Wedges allows you to also use them as set back spacers
Simply stack and invert 2, 4, and 6 sets (sold in sets of two)
Fit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt pattern
Made of strong 6061 T6 alloy aluminum (not cast aluminum)
- 65012- ML-65-5 1/2 with 5 1/2 inch set back - DIM. 18 1/8"W x 15 1/5"H Weight 32#
- 61012 - ML-65-10 with 10 inch set back - DIM. 18 1/8"W x 15 1/2"H Weight 43#
- 55012 - 2 Piece Manual w/5-1/2" setback 18 1/8" x 15 1/2"H (mounted) Weight 23#
- 40012 - 2 Piece Manual w/4" setback - DIM. 18 1/8"W x 15 1/2"H (mounted) Weight 20#
Related Products
Anchor Line and Chain
Captain Charlie's™ Anchor Line and Chain from Boaters Catalog is custom fabricated to meet your specific needs. We can custom cut any length of line or line and chain combination that you want in any sizes that you need.
The combinations that you see here are the most popular lengths and sizes that are appropriate for many electric windlasses. Please remember that not all windlasses use the same size and type of line or the same chain. Most will only pull the type of rode they are designed for. The 8 Brait line is compatible with both Lewmar and Powerwinch and will take up much less room in your anchor locker.
If you want something other than what you see here, please call 800-745-0765 or e-mail us with your specifications and we will be glad to call you back with a quote.
Freight will not be figured by the shopping cart. We will contact you when your order is received with your freight quote.close
Deluxe Step Box with Storage 2
Our Deluxe Step Box with Storage 2 has sleek rounded edges, built in non skid surface on top of the steps and Euro-style chrome brass handles.
W 22" x H 14" x D 17.5"
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products
Half Moon Boarding Mat
Our Custom Embroidered Half Moon Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your deck from marks and scratches while creating a safe way to board your boat. Our mats are seen as door mats around homes as well as on the docks and boats around the country.
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Boarding Mat can be customized with your embroidered boat name or other text, adding that personal touch.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing.
Our premium Marine Carpet Boarding Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
If you want more customization just call us at 800-745-0765/
See our other quality boat and dock products here.
37 inch High Center Console
Our 37 inch High Center Console from Boaters Catalog has a 25" x 16" mounting surface for steering and gauges and has large rounded corners. It is perfect for boats 18' to 24'.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
37"H x 31"W x 31"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
35 inch Console with Front Seat
Our 35 inch Console with Front Seat from Boaters Catalog has an overall height of 35" and an over all length including flange is 43 1/2". Rear including flange is 38" and front including flange is 32". This console is perfect for boats 21' to 25' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
Front seat is so your passenger can safely sit on the center line of the boat.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
35"H x 36"W x 43-1/2"D
Additional measurements:
- Rear width including flange 38"
- Front width including flange 32"
- Seat approx 15-1/2" high from deck
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Windlass Service Spares and Parts
Windlass Service Spares and Parts
We have access to parts for Lewmar, Horizon, Sprint, Simpson Lawrence, James Neilssen, Maxwell, and Quick. Many of the older uiits have no parts available but we won't know until we check with our US supplier. Some are available from Scotland, but they are more expensive and take a longer time to acquire.
If you need parts or service on your windlass, call us at 800-745-0765, Monday - Friday 9 am - 4 pm EST.
Single Step Box
Our Single Step Box from Boaters Catalog has sleek rounded edges, built in non skid surface on top of the steps, Euro-style chrome brass handles and all cut and exposed edges are gelcoated.
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products at this time.
25 inch Console with Seat
Our 25 inch Console with Seat from Boaters Catalog has an average fiberglass thickness of 3/8" and has a front seat molded into console. This product is perfect for boats 15' to 18' long.
25"H x 26"W x 31"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 26"W x 31"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
25 inch Center Console 01
Our 25 inch Center Console 01 from Boaters Catalog has large rounded corners and is perfect for boats 13' to 13' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 23"W x 23"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
48 inch Center Console
Our 48 inch Center Console from Boaters Catalog has large rounded corners and is perfect for boats 16' to 18' long. This product is great work boat size because it is tall and narrow.
48"H x 24"W x 24"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
This product is great work boat size because it is tall and narrow.
48"H x 24"W x 24"D
Additional measurements
- 22 inch x 14 inch section that holds the steering and controls
- 21 inch x 10 1/2 inch part that angles down from the top facing the driver
- 21 inch x 7 inch, the flat part on the top
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.