Product Information
Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates$1,460.00 – $1,684.00
The CMC HD Hydraulic Jack Plate PL-65HD Power-Lift from Boaters Catalog is designed for 400 HP outboard motors. The PL-65HD is made of 6061 T6 aluminum alloy extrusions and fastened with stainless steel fasteners for maximum strength and durability. The structure incorporates a patented roller design providing less friction, longer wear, less maintenance and virtually eliminates any chance of binding.
The self-contained and water proof electric hydraulic power unit and cylinder is embodied into one actuator inside the structure of the Power-Lift and includes its own fluid reservoir. Providing a lifting capacity of 7853 lbs of thrust, it has no problem lifting a 400 HP motor at full speed.
The CMC HD Hydraulic Jack Plate is made of 100% non-ferrous material which makes it more impervious to salt and fresh water. This design eliminates the need to install a hydraulic tank, motor, pump and hoses inside the boat saving the boat room where needed. It comes full of fluid, tested and ready for operation.
(See below for a description of transom wedges and washer plates.)
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
See all our quality CMC products for your outboard motor here.
Description
CMC HD Hydraulic Jack Plate for 400 HP
Transom Support Plates / Transom Washer Plates
Made of strong 3/8″ 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts “biting” into transoms and can more evenly distribute loads on high performance engines.
Hole centers: Top Plate – 12 7/8″ Bottom Plate – 9 7/8″
Transom Wedges and Setback Spacers (Item #20122)
These 2 degree wedges are designed to give extra positive or negative trim.
Features:
- Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed
- Unique design of the CMC Transom Wedges allows you to also use them as set back spacers
- Simply stack and invert 2, 4, and 6 sets (sold in sets of two)
- Fit all Transom jacks, jack plates, Outboard lifts, tilt trim units, and outboard motors with a standard B.I.A bolt pattern
- Made of strong 6061 T6 alloy aluminum (not cast aluminum)
Related Products
53 inch High Center Console
Our 53 inch High Center Console from Boaters Catalog has enough space to flush mount all your electronics. Dash mounting area for controls and steering is 34" x 16" and has an average fiberglass thickness of 3/8".
Base measurements including flange are 38" x 38" and height is 53".
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
53"H x 38"W x 38"D
This console is perfect for single or twin engine boats.
Freight will be quoted shortly after your order or you may call 800-745-0765 for a quote.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
Deluxe Step Box with Storage
Our Deluxe Step Box with Storage has sleek rounded edges, built-in non skid surface on top of the steps, and Euro-style chrome brass handles.
W 22" x H 12.75" x D 17.5"
Captain Charlie’s™ Heavy Water Products are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Heavy Water leads the pack in quality construction.
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
25 inch Center Console
Our 25 inch Center Console from Boaters Catalog has an average fiberglass thickness of 1/4"-3/8". Also the dash is reinforced with 11 mm Nida Core. This console is perfect for small skiffs 13'-16' long.
25"H x 21"W x 16"D
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
25"H x 21"W x 16"D
There is an 11 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
Bow Pulpit 45 Inch with hole
Our top quality fiberglass Bow Pulpit 45 Inch with hole from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
- This product has a built in non-skid surface.
- It keeps the anchor away from the deck of boat and the section that is narrow, where the shank of the anchor goes, is 4 3/4"L x 3"W.
- The front bow opening is 4 1/8" and back of opening is 5 1/4"W x 8 1/2"L.
- Weight appx. 42 pounds
- Approximate thickness is 3 inches.
- 12"Wide x 45"Long
NOTE: These are semi-custom items and are not in stock on the shelf. They are usually built and in the mold ready to take out, finish, and ship. Depending on the number of orders for the pulpits and other fiberglass items, shipping could take 1-2 weeks.
This item can not be shipped outside the Continental United States.
Freight will be quoted after your order or you can call 800-745-0765.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.https://boaterscatalog.com/nbcat/product-category/explore_product/customize/
Single Cockpit Step with Storage
Our Single Cockpit Step with Storage has sleek rounded edges, built in non skid surface on top of the steps and chrome brass handles. This step box can hold up to 250 lbs. and has Ultra-violet resistant white gelcoat.
L 20" x D 16" x H 13"
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products at this time.
Gunwale Boarding Mat
Our Custom Embroidered Gunwale Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your gunwale from marks and scratches while creating a safe way to board your boat.
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Boarding Mat can be customized with your embroidered boat name or other text, adding that personal touch.
- The Gunwale/Sideboard cover is sand weighted with 6 pound sand bag in each side at both ends (Total of 2 with each mat order) to prevent the mat from sliding during boarding or blowing overboard.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing, Our Gunnel Mat is larger than most- check your sizes before purchasing! Total size is 20" x 36" and the custom embroidery covers the 20" width of the mat.
(our mat image shows the 20" width of the mat as it lays over the gunwale)
If you don't want the name of your boat on the mat we can put "Welcome Aboard" or "Boat Shoes Only" or any short phrase of your choosing.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
15 Inch Pull Up Cleat
Our 15 Inch Pull Up Cleat from Boaters Catalog is THE LARGEST FLUSH-MOUNTED CLEAT AVAILABLE! Its the perfect cleat to keep the gunwale and bow of your vessel clean and sleek looking at the same time avoiding a trip hazard.
FEATURES:
- The largest flush-mounted cleat available!
- Made of marine grade 316 stainless steel.
- Available in both stud mount and through-bolt versions.
- Stud length is 4" on part # 115-15-S.
- Each cleat is supplied with a waterproofing cup(shown).
INSTALLATION
- Each cleat is shipped with a backing plate which also serves as the cut-out template.
- Fasten with four 3/8" diameter screws (not included),weight = 16 pounds each.
Available with visible screw holes as PN 115-15 (load of 61,000 pounds), or with studs on the underside of base as PN 115-15-S (load of 31,000 pounds).
Shipping weight 19#
Proper maintenance consists of rinsing with fresh water regularly, and following each exposure to salt water. Stainless steel surfaces should be periodically wiped with a clean, soft cloth. Plastic surfaces may be cleaned with a mild, non-abrasive detergent solution, then rinsed with fresh water as necessary.
Anchor Line and Chain
Captain Charlie's™ Anchor Line and Chain from Boaters Catalog is custom fabricated to meet your specific needs. We can custom cut any length of line or line and chain combination that you want in any sizes that you need.
The combinations that you see here are the most popular lengths and sizes that are appropriate for many electric windlasses. Please remember that not all windlasses use the same size and type of line or the same chain. Most will only pull the type of rode they are designed for. The 8 Brait line is compatible with both Lewmar and Powerwinch and will take up much less room in your anchor locker.
If you want something other than what you see here, please call 800-745-0765 or e-mail us with your specifications and we will be glad to call you back with a quote.
Freight will not be figured by the shopping cart. We will contact you when your order is received with your freight quote.close
Pull Up Cleat 209
Our Pull Up Cleat 209 from Boaters Catalog have a flat design that keeps you gunwales and bow clean looking. They are ideal for avoiding trip hazards on your boat when they are not in use.
- Sealed base eliminates the need for a waterproofing cup, water can be drained through a fitting at the bottom of the unit.
- Can be converted to a lifting cleat by inserting a connecting rod in the base of the unit and attaching the rod to the bow eye.
- Made of marine grade 316 stainless steel.
- Available in four sizes: 4 1/2", 6", 8" & 10".
- 10" version is available in both through bolt (visible screw holes) and stud-mount (no visible screw holes).
- Each cleat is shipped with a backing plate which also serves as the cut-out template..
- Screws are not included
209-4 requires quantity (4) 3/16" screws
209-6 requires quantity (4) 1/4" screws
209-8 requires quantity (4) 1/4" screws
209-10 requires quantity (4) 5/16" screws
Fiberglass Live Wells
These high quality fiberglass tanks are gel coated inside and out with a white finish outside and a blue finish inside to help keep the bait calm. The Standard tanks have a white lid for easy dipping of bait.
All our wells have no holes for water in or out so they can be custom installed on your boat with the plumbing at the correct height. They do include a drain at the bottom of the tank.
Our Heavy Water tanks are built with additional lay-ups of fiberglass and have a square clear top with stainless steel hardware.
- 30 gal. 20.5" H x 19.5" diameter
- 40 gal. 21" H x 23" diameter
- 50 gal. 24" H x 26" diameter
- 80 gal. 29.5"H x 29"W
- 100 gal. 33" H x 33.5" diameter
There is an 11 week lead time on fiberglass items at this time.
This item cannot be shipped outside the Continental United States. This item can not ship via UPS and freight will be quoted by e-mail or telephone at time of purchase. The shopping cart will not add freight to your order. We will call you with your shipping costs after your order has been received.
close
You may call us at 800-745-0765 for a quote.