Product Information
Product code: CMC-50012 Categories: Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates, Outboard Tilt and Trim$205.00
The CMC Static Jack Plate 5 inch vertical outboard motor extension allows the motor to be mounted 5 inches higher than the standard mounting height on the transom.
It is a must for easy conversion from prop drive to jet drive.
Another application includes mounting the 5 inch vertical extension on a hydraulic jack plate to raise the motor higher on shallow running boats that are equipped with tunnel extensions.
Constructed of Extruded 6061-T6 Aluminum alloy. (#50012) They are 5” wide and 20-1/2” long. It is rated for 300 HP and smaller motors.
Our offers
High Speed Hydraulic Power Lift – 10 inch setback without gauge
High_Speed Power-Lift: 10 inch setback without gauge
CMC Hydraulic Jack Plate
This dependable, self contained, and water proof CMC Hydraulic Jack Plate from Boaters Catalog has a maximum lifting capacity of 7,853 pounds of thrust. You will have no problem lifting even a V-6 300 hp max. motor at full throttle. The hydraulic actuator is mounted inside the structure of the Power-Lift, yet it is fully accessible without removing the engine. There are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks.
The catalog cannot determine freight accurately. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Description
The CMC Static Jack Plate 5 inch vertical outboard motor extension allows the motor to be mounted 5 inches higher than the standard mounting height on the transom. This vertical motor extension is a must for converting from jet drive to outboard. If you boat in shallow waters only this unit can save your skeg and prop from damage by raising it higher than normal mounting height.
LIMITED WARRANTY
CMC Marine, Inc. warrants to the first retail purchaser of its products that CMC Marine, Inc. will replace or repair the product, at its sole discretion, if any defects in material or workmanship are reported within the applicable warranty periods set out below from the date of the first retail purchase, subject to the remedies, exclusions, and limitations in this Limited Warranty. This limited warranty is effective for all CMC Marine, Inc. products purchased after January 1, 2007.
1. CMC hydraulic jack plates, CMC Tilt & Trim units: Hydraulic Actuator mechanism – 1 year
2. CMC hydraulic jack plates, manual jack plates and CMC Tilt & Trim units: frame structure assembly – 5 years
3. All other CMC Marine, Inc. Products: 1 year
See all our other quality CMC outboard engine products here.
Related Products
Bow Pulpit 60 Inch
Our top quality fiberglass Bow Pulpit 60 Inch from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
NOTE: These are semi-custom items and are not in stock on the shelf. They are usually built and in the mold ready to take out, finish, and ship. Depending on the number of orders for the pulpits and other fiberglass items, shipping could take 1-2 weeks. 3.75" high x 17" wide x 60" long
- Weight appx. 46 pounds
- Reinforced with 5/8" marine grade plywood
- Built in non-skid surface and rounded corners
This item can not be shipped outside the Continental United States.
Freight will be quoted after your order or you can call 800-745-0765.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
35 inch Console with Front Seat
Our 35 inch Console with Front Seat from Boaters Catalog has an overall height of 35" and an over all length including flange is 43 1/2". Rear including flange is 38" and front including flange is 32". This console is perfect for boats 21' to 25' long.
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
Front seat is so your passenger can safely sit on the center line of the boat.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
35"H x 36"W x 43-1/2"D
Additional measurements:
- Rear width including flange 38"
- Front width including flange 32"
- Seat approx 15-1/2" high from deck
There is an 4-6 week lead time on our fiberglass products at this time.
Freight will be quoted after your order or you can call 800-745-0765.
See more of our quality boat upgrades here.
Windlass Service Spares and Parts
Windlass Service Spares and Parts
We have access to parts for Lewmar, Horizon, Sprint, Simpson Lawrence, James Neilssen, Maxwell, and Quick. Many of the older uiits have no parts available but we won't know until we check with our US supplier. Some are available from Scotland, but they are more expensive and take a longer time to acquire.
If you need parts or service on your windlass, call us at 800-745-0765, Monday - Friday 9 am - 4 pm EST.
53 inch High Center Console
Our 53 inch High Center Console from Boaters Catalog has enough space to flush mount all your electronics. Dash mounting area for controls and steering is 34" x 16" and has an average fiberglass thickness of 3/8".
Base measurements including flange are 38" x 38" and height is 53".
Captain Charlie’s™ Center Consoles are not your everyday cookie cutter products that you see in many marine stores. They are high end, high quality, yet affordable products that have been missing from the market. We take great pride in the quality of all our products and Captain Charlie’s™ Consoles leads the pack in quality construction.
There is a plywood sandwich in the area where the steering wheel and throttle control are to be mounted. Flange along the bottom is for mounting to the deck of the boat.
53"H x 38"W x 38"D
This console is perfect for single or twin engine boats.
Freight will be quoted shortly after your order or you may call 800-745-0765 for a quote.
There is an 4-6 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.
Bow Pulpit 33 Inch
This top quality Bow Pulpit 33 Inch from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
33in long x 11in wide at the bow x 3in thick
- Tapers to approximately 7 1/2 wide at the end
- Weight 18 pounds
- Approximate thickness is 2 1/5 to 2 3/4 inches.
This item can not be shipped outside the Continental United States.
There is an 11 week lead time for all fiberglass products right now.
See more of our quality boat products here.
Fiberglass Live Wells
These high quality fiberglass tanks are gel coated inside and out with a white finish outside and a blue finish inside to help keep the bait calm. The Standard tanks have a white lid for easy dipping of bait.
All our wells have no holes for water in or out so they can be custom installed on your boat with the plumbing at the correct height. They do include a drain at the bottom of the tank.
Our Heavy Water tanks are built with additional lay-ups of fiberglass and have a square clear top with stainless steel hardware.
- 30 gal. 20.5" H x 19.5" diameter
- 40 gal. 21" H x 23" diameter
- 50 gal. 24" H x 26" diameter
- 80 gal. 29.5"H x 29"W
- 100 gal. 33" H x 33.5" diameter
There is an 11 week lead time on fiberglass items at this time.
This item cannot be shipped outside the Continental United States. This item can not ship via UPS and freight will be quoted by e-mail or telephone at time of purchase. The shopping cart will not add freight to your order. We will call you with your shipping costs after your order has been received.
close
You may call us at 800-745-0765 for a quote.
Anchor Line and Chain
Captain Charlie's™ Anchor Line and Chain from Boaters Catalog is custom fabricated to meet your specific needs. We can custom cut any length of line or line and chain combination that you want in any sizes that you need.
The combinations that you see here are the most popular lengths and sizes that are appropriate for many electric windlasses. Please remember that not all windlasses use the same size and type of line or the same chain. Most will only pull the type of rode they are designed for. The 8 Brait line is compatible with both Lewmar and Powerwinch and will take up much less room in your anchor locker.
If you want something other than what you see here, please call 800-745-0765 or e-mail us with your specifications and we will be glad to call you back with a quote.
Freight will not be figured by the shopping cart. We will contact you when your order is received with your freight quote.close
Single Cockpit Step with Storage
Our Single Cockpit Step with Storage has sleek rounded edges, built in non skid surface on top of the steps and chrome brass handles. This step box can hold up to 250 lbs. and has Ultra-violet resistant white gelcoat.
L 20" x D 16" x H 13"
Shipping on our steps will be quoted at time of sale. You may call 800-745-0765 for a freight quote.
There is an 11 week lead time on our fiberglass products at this time.
Half Moon Boarding Mat
Our Custom Embroidered Half Moon Boarding Mat from Boaters Catalog is a plush yet durable cover that protects your deck from marks and scratches while creating a safe way to board your boat. Our mats are seen as door mats around homes as well as on the docks and boats around the country.
- Made from our UV resistant, marine grade carpet material and backed with a non-skid, non-marking rubber that won't deteriorate over time.
- Our Boarding Mat can be customized with your embroidered boat name or other text, adding that personal touch.
- Longest warranty in the Marine Industry EIGHT YEARS Full Warranty on carpet and backing.
Our premium Marine Carpet Boarding Mat an essential accessory for any boating enthusiast . All are made of a plush carpet that is waterproof, stain and fade resistant, mold and mildew resistant, with a non-skid rubber backing. All edges are beautifully finished with matching poly binding. They are available in a wide variety of shapes, colors, and styles. We provide custom embroidery to match.
All our mats and carpets are custom cut and embroidered to order. The lead time is appx. 4-6 weeks from the time of your order until it is shipped due to raw materials being held up in shipping.
If you want more customization just call us at 800-745-0765/
See our other quality boat and dock products here.
Bow Pulpit 49 inch
This top quality fiberglass Bow Pulpit 49 inch from Boaters Catalog is built to exacting specifications and will fit almost all bow configurations.
The skirt all the way around the bottom of the pulpit can be cut to match the toe rail or angle of the deck on your boat in order to make a seamless appearing installation.
NOTE: These are semi-custom items and are not in stock on the shelf. They are usually built and in the mold ready to take out, finish, and ship. Depending on the number of orders for the pulpits and other fiberglass items, shipping could take 1-2 weeks. 2" high x 16" wide x 49" long
- Weight appx. 40 pounds
- Approximate thickness is 2 1/5 to 2 3/4 inches.
This item can not be shipped outside the Continental United States.
Freight will be quoted after your order or you can call 800-745-0765.
There is an 11 week lead time on our fiberglass products at this time.
See more of our quality boat upgrades here.