-
Bow Pulpit 45 Inch with hole
Qty: 1$584.00 -
Troll Plate Fin
Qty: 1$78.00
Total:
$662.00
Important Information...
Online Policies
International Sales
Shipping and Returns
Your Privacy Matters
Talk to Us!
Description
Description
Minnow Fin For Trolling Motors
The Minnow from Boaters Catalog installs in minutes with just a screwdriver. It will provide directional assistance whenever it is in the water. The steering response is improved when using thrust or when using another motor for propulsion. If fishing conditions require drifting and working the current while stalking the ‘Elusive Lunker’ the minnow will add stability and limit wind effect. Fight the fish, not your boat. Tested and proven effective by Northwest fishermen.
BENEFITS
- 10X the Steering Control
- 3X the Turn Rate
- 10X the Effective Rudder Area
- Exceptional Tracking in Windy and Turbulent Conditions
- Reduced Cycling of the Autopilot because the steering is more effective.
- Maximizes the thrust of your electric trolling motor.
FEATURES
- Marine Aluminum
- Welded construction
- Fits virtually all modern electric trolling motors
- Simple 5 minute installation with only a screw driver.
- Patent Pending
- Made in the USA
Related Products
Quick View
Orca Heavy Duty Performance Fin
The Orca Heavy Duty Performance Fin from Boaters Catalog triples the effective rudder area providing a tighter turn radius and sharp crisp 
directional control at any speed. The larger surface area of the Orca Heavy Duty Performance Fin blocks cavitation better than hydrofoils while adding the benefit of enhanced slow speed maneuvering and heading control. The Orca Heavy Duty Performance Fin installs in minutes without drilling using the 45M-Clamp kit or bolt directly to the cavitation plate using included hardware.
The Orca fin is usually mounted with the fins down but may be installed fins up without modification if you desire less aggressive control. Used and tested on fishing boats, runabouts, pontoon boats, cruisers, ski boats and bass boats over 250 HP.
Quick View
PT130 Tilt and Trim
The CMC PT-130 Tilt and Trim for up to 130 HP from Boaters Catalog allows you to tuck your motor in to get your boat on plane smoother and faster. When you’re underway, you can change the angle of your motor to obtain the best performance for your load and water conditions. It gives you a more stable ride, increases top end speed, allows more prop clearance, and better fuel economy.
Electric Hydraulic Tilt & Trim
You Get Power Tilt & Trim, Better Boat Handling, More Speed, Lower Fuel Consumption and No More Back Strain!
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
See all our quality CMC products for your outboard here.
Price range: $954.00 through $1,133.00
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Boat Tool Holder
Customize Your Vessel, Fishing Tools, Improve the hardware on your boat, Improve your beach or dock fishing experience, Improve your fishing tackle, Other Boat Hardware, Snap-N-Trac Organizer System
All-in-one, customizable Boat Tool Holder from Boaters Catalog for lures, pliers, knives, hook extractor, and cup holder.
Customize the Snap-N-Trac the way you want! 3 different designs with the one kit.
Lay the pieces out any way you like. Simply attach the trac then snap in the pieces in the design you prefer.
Can be installed where other systems cannot!
Add more kits to hold more stuf!
Quick View
Dolphin Trolling Fin
The Dolphin Trolling Fin from Boaters Catalog gives you an edge on the water by providing exceptional tracking in wind and turbulent conditions. The Fin triples the effective rudder area which improves your stability, increases your ability to turn and reduces the cycle time on your auto-pilot system. The Dolphin-Trolling Fin installs in minutes without drilling using the 45M-Clamp kit or bolt directly to cavitation plate using included hardware. Tested and approved by Alaska and Northwest fishing guides.
Recommended for motors less than 79 Horsepower with up to a 12" Diameter Prop
Quick View
Tie Down and Ski Tow
Flush Mounted Tie Down and Ski Tow
Tie Down Features
- May be used anywhere equipment must be secured to the deck-e.g. poling platform, scuba gear, fenders, etc.
- Large size (#195) is also ideal for docks; small size (#196) is ideal for personal watercraft.
- Made of cast stainless steel.
- Assembly consists of main body and sealing cup.
Ski Tow Features:
- Keeps the transform clear of protruding ski tows.
- Four piece patented assembly consists of main body, sealing cup, backing plate and gasket.
Price range: $20.65 through $55.87
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Static Jack Plate 5 inch
Customize Your Vessel, Maintain or improve your engine, Outboard Jack Plates, Outboard Tilt and Trim
The CMC Static Jack Plate 5 inch vertical outboard motor extension allows the motor to be mounted 5 inches higher than the standard mounting height on the transom.
It is a must for easy conversion from prop drive to jet drive.
Another application includes mounting the 5 inch vertical extension on a hydraulic jack plate to raise the motor higher on shallow running boats that are equipped with tunnel extensions.
Constructed of Extruded 6061-T6 Aluminum alloy. (#50012) They are 5” wide and 20-1/2” long. It is rated for 300 HP and smaller motors.
Quick View
Through Hull Fittings
Customize Your Vessel, Improve the hardware on your boat, Lifting Cleats, Eyes, and Chocks, Other Boat Hardware, Pop Up and Pull Up Cleats
Through hull fittings for drains for your pull up or pop up cleats, lifting rings, or other hardware that you don't want to drain inside the boat.
| PRODUCT # | DESCRIPTION |
| 600 | Brass through hull fitting |
| 601 | Plastic through hull fitting |
| 602 | Stainless Steel through hull fitting |
- For up to 1/4" thick hulls.
- Available in plastic, stainless steel or brass.
- Thread is 3/8-24.
Price range: $4.51 through $11.57
Select options
This product has multiple variants. The options may be chosen on the product page
Quick View
Engine Control Service
To properly service your Hydraulic Engine and Transmission Control Maintenance and Service contact Boaters Catalog at 800-745-0765 or fill in your information here to send your units to us.
Teleflex/Morse / Hynautic is the world’s largest manufacturer of marine hydraulic controls
- Proven performance and reliability for over 30 years
- Dependable control for luxury cruisers, workboats and commercial fishing boats
- Nothing moves boats better a hydraulic control is a liquid link between a sender and an actuator
- Provides pure energy in motion without friction, without backlash, no lost motion up to four stations is possible depending on length of tubing run
- Unique and highly accepted feel
- Simple installation
Quick View
Jet Ski Ladder
Customize Your Vessel, Boarding Steps and Ladders, Dock Ladders, Gift giving, Improve the hardware on your boat, Other Boat Hardware
Jet Ski Ladder from EZ Riser™ is a flexible 2 boarding step ladder that fits NEWER personal watercraft. Made from the finest American made materials, EZ Riser is a flexible boarding step that fits most personal watercraft. Simply loop the rope through the back “D” clamp, then back through itself securing it to the “D” clamp.
- Installs in seconds,
- No tools required,
- Extremely convenient,
- Stores easily on back “D” clamp.
- Adjustable and transferable,
- No mooring interference,
- UV-treated for long life,
- Can also be used on jet boats,
- 300 pound capacity.
Other Boats that use the EZ Riser Flexible Boarding Ladder are:
- Bass Boats... sits on a cleat and ready when you are.
- Walkarounds... just attach it to a cleat and use it when you need it.
- Skiffs... same solution, attach it to a cleat and forget about it.
- Sail Boats... used as an emergency access to a sailboat with no affixed ladder.
- All others... as long as you can reach the gunnels from the water, you can use it.
Quick View
Static Jack Plates
CMC Static Jack Plates
The 2-1/2 INCH CMC Static Setback Jack Plate has 1 ½” of height adjustment at the transom. It can be used as a stand-alone 2 ½” setback plate or used in conjunction with another manual or hydraulic jack plate to give an additional 2 ½” of setback. Constructed of Extruded 6061-T6 Aluminum alloy. (#65213)
The 7 INCH CMC Static Setback Jack Plate has 1 ½” of height adjustment at the transom bracket and 1” of height adjustment on the motor bracket. The dimension from the top of the transom to the top of the motor side is 3 ½”. Constructed of Extruded 6061-T6 Aluminum alloy and stainless steel fasteners. (#70012)
The 9 INCH CMC Static Setback Jack Plate has 1 ½” of height adjustment at the transom and 1” of height adjustment on the motor bracket. The dimension from the top of the transom to the top of the motor side is 5 ¾”. Constructed of Extruded 6061-T6 Aluminum alloy and stainless steel fasteners. (#90012)
All our CMC Static Setback Jack Plates are built of the finest quality materials and made to accept any bolt pattern for ease of installation.
The catalog cannot determine freight accurately for these products. We will contact you after the sale with the correct freight. If you wish, you may call us at 800-745-0765 for a freight quote prior to ordering.
Price range: $148.00 through $439.00
Select options
This product has multiple variants. The options may be chosen on the product page
